Top 23 Vacuum Traps for 2019

 

Laboy HMV010115 Glass Vacuum Trap with 10 mm Serrated Hose 200 mm Length Below the 2440 Joint #ad

Laboy HMV010115 Glass Vacuum Trap with 10 mm Serrated Hose, 200 mm Length Below the 24/40 Joint

Laboy HMV010115 Glass Vacuum Trap with 10 mm Serrated Hose, 200 mm Length Below the 24/40 Joint #ad - D. Center tube hose connection is always 10mm for easy connection to manifold bank tubes which are also with 10mm hose connection. Vacuum trap, also called cold trap, is used to condense all vapors except the permanent gases into a liquid or solid. Laboy glass flasks are heavy wall designed, made by hand-blowing to ensure uniform wall thickness, made of high-quality borosilicate glass and annealed at 800 degree celsius, can be heated directly in an open flame and can withstand typical laboratory thermal variations in chemistry processes like heating and cooling. Serrated hose connections for side tube have an o. Of 13mm at the smallest serration and 16mm at the largest serration. With joint for easy removal of condense.

 

Chemglass CG-4529-04  Series CG-4529 Vacuum Trap Body for Model CG-4529-01 1000 mL Capacity #ad

Chemglass CG-4529-04 Series CG-4529 Vacuum Trap Body for Model CG-4529-01, 1000 mL Capacity

Chemglass CG-4529-04 Series CG-4529 Vacuum Trap Body for Model CG-4529-01, 1000 mL Capacity #ad - Connections are 1/2in o. Trap is designed to fit into standard cg-1593 through cg-1595 dewar flasks. D. Trap is designed for large volume solvent removal by vacuum. The 40/35 standard taper joint connects trap body with stopper.

 

Laboy HMV010212 Glass Vacuum Trap with 4550 Joint 250 mm Length Below Joint 22 mm Tube OD #ad

Laboy HMV010212 Glass Vacuum Trap with 45/50 Joint 250 mm Length Below Joint 22 mm Tube O.D.

Laboy HMV010212 Glass Vacuum Trap with 45/50 Joint 250 mm Length Below Joint 22 mm Tube O.D. #ad - Was founded in 1999, focusing on the research, development, manufacture, sale and after-sales service of laboratory equipment. , Ltd. Beijing weichengya laboratory equipment co. With joints for easy removal of condensate. Body length is measured below the joint.

 

Chemglass CG-4510-04  Series CG-4510 Vacuum Trap 38 mm OD 18 mm OD Side and Inner Tube 250 mm Length #ad

Chemglass CG-4510-04 Series CG-4510 Vacuum Trap, 38 mm OD, 18 mm OD Side and Inner Tube, 250 mm Length

Chemglass CG-4510-04 Series CG-4510 Vacuum Trap, 38 mm OD, 18 mm OD Side and Inner Tube, 250 mm Length #ad - One piece trap used in the removal of undesired vapors in the vacuum system by condensation. , 38mm od, 250mm length, 18mm od side and inner tube.

 

Chemglass CG-4530-01 Complete Vacuum Trap #ad

Chemglass CG-4530-01 Complete Vacuum Trap

Chemglass CG-4530-01 Complete Vacuum Trap #ad - The unique design of the stopper decreases the chance of freezing by allowing vapor to pass through the holes in the side of the inner tube. The 55/50 standard taper joint connects the trap body with the stopper. Hose connections are 15mm od at the largest serration. Trap is designed for high volume solvent removal by vacuum.

 

Chemglass CG-4515-20 Complete Serrated Hose Connection Vacuum Trap with 5550 Joint 60mm OD x 300mm Overall Length #ad

Chemglass CG-4515-20 Complete Serrated Hose Connection Vacuum Trap with 55/50 Joint, 60mm OD x 300mm Overall Length

Chemglass CG-4515-20 Complete Serrated Hose Connection Vacuum Trap with 55/50 Joint, 60mm OD x 300mm Overall Length #ad - Two piece construction for easy removal of condensate. Of 13mm at the smallest serration and 16mm at the largest serration. Body length is the overall length from the top of the joint to the bottom of the round bottom. Inlet and outlet are 180° apart for installation into a variety of vacuum systems. Serrated hose connections have an o. Stopper has a standard taper inner joint and body has an outer joint. D.

 

Goldleaf Scientific - Vacuum Cold Trap with 10mm Serrated Hose Barbs 225mm Length Below the 3445 Joint #ad

Goldleaf Scientific – Vacuum Cold Trap with 10mm Serrated Hose Barbs & 225mm Length Below the 34/45 Joint

Goldleaf Scientific – Vacuum Cold Trap with 10mm Serrated Hose Barbs & 225mm Length Below the 34/45 Joint #ad - It is crucial to protect your vacuum pump in order to reach and maintain the required vacuum level, and prevent costly and unnecessary oil changes. A vacuum trap or “cold trap” is used to prevent vapors from entering your vacuum pump and contaminating your vacuum pump oil. If your vacuum pump ingests vapor it can be detrimental to performance and longevity of the pump.

 

Chemglass CG-4513-11 Vacuum Trap with 40 O-Ring Joint 45mm OD x 250mm Length #ad

Chemglass CG-4513-11 Vacuum Trap with #40 O-Ring Joint, 45mm OD x 250mm Length

Chemglass CG-4513-11 Vacuum Trap with #40 O-Ring Joint, 45mm OD x 250mm Length #ad - Complete trap is supplied with a stopper, lower body, viton o-ring, and uses. Serrated hose connections are 13. 5mm at the smallest serration and 15. Pinch clamp. O-ring joint provides for a vacuum tight, grease free seal and permits the trap body to be easily disconnected from the stopper for cleaning. Similar to cg-4515 traps but having an o-ring joint to connect the trap body to the stopper. 5mm at the largest serration.

 

Corning Pyrex Borosilicate Glass Vacuum Trap Separable 5050 Standard Taper Inner and Outer Joint 48mm OD x 250mm L #ad

Corning Pyrex Borosilicate Glass Vacuum Trap, Separable, 50/50 Standard Taper Inner and Outer Joint, 48mm OD x 250mm L

Corning Pyrex Borosilicate Glass Vacuum Trap, Separable, 50/50 Standard Taper Inner and Outer Joint, 48mm OD x 250mm L #ad - With standard taper joint 2 piece unit. Body lengths specified exclude joint inlet tube extends to approximately 25 mm from bottom. Body od x length, inlet tube od x length and standard taper joint size shown in table. Top and side tubulations are 75 mm long and have same od specified for inlet tube in listings.

 

Laboy HMV010116 Glass Vacuum Trap with 10 mm Serrated Hose 200 mm Length Below The 2942 Joint #ad

Laboy HMV010116 Glass Vacuum Trap with 10 mm Serrated Hose 200 mm Length Below The 29/42 Joint

Laboy HMV010116 Glass Vacuum Trap with 10 mm Serrated Hose 200 mm Length Below The 29/42 Joint #ad - Serrated hose connections for side tube have an o. With joint for easy removal of condense. Laboy glass flasks are heavy wall designed, made by hand-blowing to ensure uniform wall thickness, made of high-quality borosilicate glass and annealed at 800 degree celsius, can be heated directly in an open flame and can withstand typical laboratory thermal variations in chemistry processes like heating and cooling. D. Center tube hose connection is always 10mm for easy connection to manifold bank tubes which are also with 10mm hose connection. Of 13mm at the smallest serration and 16mm at the largest serration. Vacuum trap, also called cold trap, is used to condense all vapors except the permanent gases into a liquid or solid.

 

Corning Pyrex Borosilicate Glass Vacuum Trap Separable 2942 Standard Taper Inner and Outer Joint 28mm OD x 200mm L Case of 4 #ad

Corning Pyrex Borosilicate Glass Vacuum Trap, Separable, 29/42 Standard Taper Inner and Outer Joint, 28mm OD x 200mm L (Case of 4)

Corning Pyrex Borosilicate Glass Vacuum Trap, Separable, 29/42 Standard Taper Inner and Outer Joint, 28mm OD x 200mm L (Case of 4) #ad - Body lengths specified exclude joint inlet tube extends to approximately 25 mm from bottom. Top and side tubulations are 75 mm long and have same od specified for inlet tube in listings. Body od x length, inlet tube od x length and standard taper joint size shown in table. With standard taper joint 2 piece unit.

 

Chemglass CG-4516-02  Series CG-4516 Vacuum Trap Stopper 2942 Joint #ad

Chemglass CG-4516-02 Series CG-4516 Vacuum Trap Stopper, 29/42 Joint

Chemglass CG-4516-02 Series CG-4516 Vacuum Trap Stopper, 29/42 Joint #ad - , 29/42 joint, sold in each, manufactured by chemglass. Similar to cg-4514, but with the top inlet tube bent at a 90° angle.

 

Chemglass CG-4514-16  Series CG-4514 Vacuum Trap Body 5550 Joint #ad

Chemglass CG-4514-16 Series CG-4514 Vacuum Trap Body, 55/50 Joint

Chemglass CG-4514-16 Series CG-4514 Vacuum Trap Body, 55/50 Joint #ad - Two piece vacuum trap connected with an inner and outer joint to facilitate cleaning. , 55/50 joint, sold in each, manufactured by chemglass.

 

2 Quart Resin Trap Vacuum Degassing Chamber #ad

2 Quart Resin Trap/ Vacuum & Degassing Chamber

2 Quart Resin Trap/ Vacuum & Degassing Chamber #ad - -60a durometer density • (1) glycerin filled vacuum gauge (must be regulated upon arrival) -max vacuum -29hg (+/-. The maximum allowed temperature of this chamber is 160f. No adhesives are used our simple gasket design even allows you to place the lid on the chamber somewhat off center and still pull a full vacuum. This is a complete bestvaluevac® vacuum chamber setup designed built and 100% tested in chicago, illinois. The gasket itself is reversible (doubling the life of our system) allowing customers to instantly take it off and flip it over. Every chamber is tested prior to shipping to lose no more than 2. This kit includes • (1) 1. 5 gallon high strength stainless steel chamber • (1) industrial grade silicone gasket -gasket can withstand 390f max temp. 5hg) at sea level • (1) leak free nickel plated air manifold -vacuum release valve and vacuum connect valve • (1) 1/4 female flare universal pump adapter for vacuum hose • (1) 5ft clear steel reinforced vacuum hose • (1) 8″x8″ platinum cured silicone non stick vacpad® • (1) 50 micron air filter. 5hg/24hrs. With our unique patent pending gasket design (utility patent #14/533,548) this chamber is sure to last 10,000 uses with proper care and maintenance. This is a feature that most other vacuum chambers do not offer. The components of this chamber are rated at higher temperatures however as a vacuum vessel we limit maximum operational temperature to 160f.

 

Goldleaf Scientific Vacuum Cold Trap w 10mm Serrated Hose 250mm Length Below the 4550 Joint #ad

Goldleaf Scientific Vacuum Cold Trap w/ 10mm Serrated Hose, 250mm Length Below the 45/50 Joint

Goldleaf Scientific Vacuum Cold Trap w/ 10mm Serrated Hose, 250mm Length Below the 45/50 Joint #ad - If your vacuum pump ingests vapor it can be detrimental to performance and longevity of the pump. A vacuum trap or “cold trap” is used to prevent vapors from entering your vacuum pump and contaminating your vacuum pump oil. It is crucial to protect your vacuum pump in order to reach and maintain the required vacuum level, and prevent costly and unnecessary oil changes.

 

Chemglass CG-4516-14  Series CG-4516 Vacuum Trap Complete 60 mm OD 30 mm OD Side and Inner Tube 5550 Joint 300 mm Length #ad

Chemglass CG-4516-14 Series CG-4516 Vacuum Trap Complete, 60 mm OD, 30 mm OD Side and Inner Tube, 55/50 Joint, 300 mm Length

Chemglass CG-4516-14 Series CG-4516 Vacuum Trap Complete, 60 mm OD, 30 mm OD Side and Inner Tube, 55/50 Joint, 300 mm Length #ad - , 60mm od, 30mm od side and inner tube, 55/50 joint, 300mm length. Similar to cg-4514, but with the top inlet tube bent at a 90° angle.

 

Laboy HMV010201 Glass Vacuum Trap with 3520 Ball Joints 50 mm Body OD250 mm Length Below 4550 Joint #ad

Laboy HMV010201 Glass Vacuum Trap with 35/20 Ball Joints 50 mm Body O.D.250 mm Length Below 45/50 Joint

Laboy HMV010201 Glass Vacuum Trap with 35/20 Ball Joints 50 mm Body O.D.250 mm Length Below 45/50 Joint #ad - Vacuum trap, also called cold trap, is used to condense all vapors except the permanent gases into a liquid or solid. For use with vacuum manifolds having 35/20 socket joints. Laboy glassware are heavy wall designed, made by hand-blowing to ensure uniform wall thickness, made of high-quality borosilicate glass and annealed at 800 degree celsius, can be heated directly in an open flame and can withstand typical laboratory thermal variations in chemistry processes like heating and cooling. With joint for easy removal of condense. Center tube hose connection is always 10mm for easy connection to manifold bank tubes which are also with 10mm hose connection. Please order the pump adapter and socket clamp separately.

 

Chemglass CG-4515-04 Complete Serrated Hose Connection Vacuum Trap with 5050 Joint 54mm OD x 275mm Overall Length #ad

Chemglass CG-4515-04 Complete Serrated Hose Connection Vacuum Trap with 50/50 Joint, 54mm OD x 275mm Overall Length

Chemglass CG-4515-04 Complete Serrated Hose Connection Vacuum Trap with 50/50 Joint, 54mm OD x 275mm Overall Length #ad - Of 13mm at the smallest serration and 16mm at the largest serration. Inlet and outlet are 180° apart for installation into a variety of vacuum systems. D. Body length is the overall length from the top of the joint to the bottom of the round bottom. Serrated hose connections have an o. Stopper has a standard taper inner joint and body has an outer joint. Two piece construction for easy removal of condensate.

 

Laboy HMV010209 Glass Vacuum Trap with 2942 Joint 200 mm Length Below Joint 10 mm Tube OD #ad

Laboy HMV010209 Glass Vacuum Trap with 29/42 Joint 200 mm Length Below Joint 10 mm Tube O.D.

Laboy HMV010209 Glass Vacuum Trap with 29/42 Joint 200 mm Length Below Joint 10 mm Tube O.D. #ad - Body length is measured below the joint. With joints for easy removal of condensate. Was founded in 1999, focusing on the research, development, manufacture, sale and after-sales service of laboratory equipment. Beijing weichengya laboratory equipment co. , Ltd.

 

Laboy HMV010105 Glass Vacuum Trap with 15 O-Ring Joint and 4550 Taper Joint 50 mm OD #ad

Laboy HMV010105 Glass Vacuum Trap with #15 O-Ring Joint and 45/50 Taper Joint 50 mm O.D.

Laboy HMV010105 Glass Vacuum Trap with #15 O-Ring Joint and 45/50 Taper Joint 50 mm O.D. #ad - Laboy glass flasks are heavy wall designed, made by hand-blowing to ensure uniform wall thickness, made of high-quality borosilicate glass and annealed at 800 degree celsius, can be heated directly in an open flame and can withstand typical laboratory thermal variations in chemistry processes like heating and cooling. D of inner and side tube is 18mm. Vacuum trap, also called cold trap, is used to condense all vapors except the permanent gases into a liquid or solid. The length of outer body below joint is 250mm, the o. Supplied with two asr116 ptfe o-rings. Capacity of 500ml.

 

Wilmad-LabGlass LG-11065-100 Dewar Shape Vacuum Trap 2L #ad

Wilmad-LabGlass LG-11065-100 Dewar Shape Vacuum Trap, 2L

Wilmad-LabGlass LG-11065-100 Dewar Shape Vacuum Trap, 2L #ad - Designed to remove relatively large volumes of solvent, these borosilicate glass vacuum traps can be used with rotary evaporators. Lower reservoir has a ptfe valve to remove condensate. Inner cylinder is charged with dry ice/alcohol or liquid nitrogen.

 

VACUUM TRAP DEWAR TYPE G 1L #ad

VACUUM TRAP DEWAR TYPE G 1L

VACUUM TRAP DEWAR TYPE G 1L #ad - Vacuum trap, dewar type, synthware, capacity 1000ml, stopcock glass, stopcock bore 4mm.

 

Chemglass Glass 500mL Vacuum Trap 130mm W x 360mm H Body and Stopper Only #ad

Chemglass Glass 500mL Vacuum Trap 130mm W x 360mm H Body and Stopper Only

Chemglass Glass 500mL Vacuum Trap 130mm W x 360mm H Body and Stopper Only #ad - Biotech bargains california chemglass glass 500ml vacuum trap 130mm w x 360mm h body and stopper onlyno cracks or chips. 9. Thorough cleaning and sterilization are recommended before use. #40 o-ring  (cg-305-226) and clamp (cg-150-09) not included. 8b2 (627)).  _gsrx_vers_627 (gs 6.   This product can not be intended for use in either human or animal food manufacturing processes or related purposes.





We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites.